Question: Will a 351 Windsor fit a 302 transmission?

Stock 302 headers will bolt up to the head of a 351w (since the heads are basically the same), but will not mate up to the factory 302 mid-pipe due to the extra width of the 351w, and may even make contact with the transmission tunnel.

What transmission goes with a 351 Windsor?

A C-4 is a good reliable trans and will fit behind a 351W no problem. An AOD is another good option if you want taller gears and manners for highway cruising…

Will a 302 intake fit a 351 Windsor?

Intake won’t cross over, The 351 has a taller deck than the 302. The timing cover will bolt on but ford used three different timing marks so it may not be right for the damper, which also must match the flex plate balance and the engine should have been balanced to match both.

Is a 302 bellhousing the same as a 351?

Registered. +1. Keep in-mind, there are different versions of each component, and while any 302 components will work on a 351W (except 1980+ 302/5.0L flywheels – wrong balance), the component types must match each other. The most basic factor is 157-tooth or 164-tooth flywheel.

THIS IS IMPORTANT:  You asked: Is General Motors American made?

Will a 302 computer run a 351?

A 302 MA computer would run your future 351 with GT40 irons, mild cam, intake, exhaust. Finding these truck computers is no easy task.

Will a C6 transmission bolt up to a 351 Windsor?

Registered. — No, that 351W will not bolt onto your 351M C6. — No, all 351W engines used the 351W bellhousing pattern, shared by the 302, 289, 351C, and 300-I6. — Your C6 uses a pattern shared by the 351M/400M (same engine block), and 429/460.

Which is better C4 or C6 transmission?

The C4 transmission was primarily used in cars. The C6 transmission could handle more power. Due to the ability to handle more power, the C6 transmission was used in many Ford trucks with bigger engines, and in larger cars that were manufactured with bigger engines.

What parts are interchangeable between 302 and 351W?

302 heads are basically the same as the 351w heads with the exception of the head bolt diameter. 302 heads have a 7/16” head bolt hole and the 351w has a ½” head bolt. Opening the holes can be done by hand, if done with care.

Are 302 and 351W oil pans the same?

The 351W pan has a larger diameter rear seal than it’s 302 counterpart, and a larger front sump to accomadate the larger 351W oil pump.

Are all 5.0 blocks the same?

With the exception of the Boss 302, all intakes for the 289/302/5.0 are interchangeable. Blocks went roller starting in 1985 and got better in 1987. The non roller blocks from 1980 to 84 are to be avoided. These were the lightweights, litterally.

THIS IS IMPORTANT:  Does a new transmission have a break in period?

Are Cleveland and Windsor Bellhousings the same?

It is part of the long-running Ford small-block Windsor V8 family, which also includes the venerable Ford 302 (5.0L) V8. It shares the same small block V8 bellhousing pattern and motor mounts of the August 1964+ Windsor engines*. … The patterns are not interchangeable.

What does a T5 transmission come in?

There are two basic types of T5 transmissions—the original T-5 STD (Non-World Class or NWC) and the World Class T5 (WC).

What litter is a 351?

Basically, the 351M/400 is a tall-deck version of a 351C. A 351C is considered by most Ford enthusiasts as a “smallblock” because it shares the same bellhousing as the Windsor family of engines (221/260/289/302/351W).

Encyclopedia auto repair